GripEdge | 20-PC RPT™ 1/4", 3/8" & 1/2" Drive Standard Metric Hex Master Bit Socket Set
Limited Lifetime Warranty
Against manufacturing and workmanship defects (Excluding Drill Bits)
Free shipping
Anywhere in the US on orders over 99$
Best in class
Market leader in preventing rounded fasteners
Hex fasteners fail in one of two ways. A tight socket cap screw rounds its broach when a standard bit contacts only the corners and wedges material outward under load, or the broach is already rounded and a standard bit has nothing left to bear against. The MMH20S 20-PC RPT™ Standard Metric Hex Master Bit Socket Set covers both cases across the entire metric range: twenty continuous sizes from 1.5mm through 19mm on 1/4", 3/8", and 1/2" square drive, so every metric hex fastener you meet, from a trim screw to a caliper bracket bolt, gets a bit on the correct drive size with the same engagement geometry.
Every socket is built on the same patented RPT™ profile, so prevention and extraction behavior is consistent from the smallest 1.5mm bit to the largest 19mm.
What's in the set
- Metric Hex (20): 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm, 12mm, 13mm, 14mm, 15mm, 16mm, 17mm, 18mm, 19mm
- Square drive: 1/4", 3/8", and 1/2", each size on the drive matched to its torque range
- Storage: Durable case with foam insert
The engineering behind the grip
- RPT™ tooth geometry that loads inward. Standard hex tools concentrate stress on the fastener corners and push material outward, which is what rounds a broach. The RPT™ profile relocates the contact point along the flank and directs force inward, forming a mechanical lock. Torque transfers into the fastener rather than around it, delivering up to 50% more grip on new fasteners and up to 400% more grip on damaged ones.
- Prevention and extraction in one tool. Because RPT™ grips new and compromised fasteners alike, these are not special-occasion tools. Reach for them first, every time, to prevent rounding before it starts, and rely on the same bits to remove a fastener that has already been chewed up, no separate extractor set required.
- Bi-directional engagement. The profile grips in both directions for loosening and tightening. When a replacement is not on hand, RPT™ can grip a damaged fastener well enough to drive it back in temporarily.
- Replaces standard Hex tools. Full 1.5mm through 19mm coverage on three drive sizes means this case takes the place of the standard hex bit socket sets in the drawer rather than sitting beside them.
- Material and marking. S2 steel with a zinc phosphate finish for strength, durability, and corrosion resistance, with oversized roll-stamped, ink-filled size markings for legibility in low light.
Twenty sizes, three drives, one gripping principle from 1.5mm to 19mm.
Specifications
| SKU | MMH20S |
|---|---|
| Product family | Hand Drive Sockets |
| Category | Bit Sockets |
| Configuration | Set |
| Fastener profile | Hex |
| Profile style | Straight-End |
| Metric sizes | 1.5 mm, 2 mm, 2.5 mm, 3 mm, 4 mm, 5 mm, 6 mm, 7 mm, 8 mm, 9 mm, 10 mm, 11 mm, 12 mm, 13 mm, 14 mm, 15 mm, 16 mm, 17 mm, 18 mm, 19 mm |
| Square drive | 1/2 in, 1/4 in, 3/8 in |
| Length | Standard |
| Storage | Case + Foam |
| Technology | RPT™ |